Differences

This shows you the differences between two versions of the page.

--- home:technologies:micropowermanager [2025/01/17 14:56] – [DS1600 Single Phase Smart Prepayment Meter ] rahul
+++ home:technologies:micropowermanager [2025/01/17 15:04] (current) – [Data Concentrator Unit DSC100] rahul
@@ Line 49: / Line 49: @@
 Many Pay-As-You-Go (PAYG/PAYGO) systems are based on 2G/GPRS communications. But as 2G towers get replaced by 3G and 4G infrastructure, energy access organizations around the world will need to update their hardware. Okra's communications solution, Cicada, is an open source module with 2G, 3G, 4G, and WiFi capabilities.
-===== Previous generation DS1000 Single Phase Prepayment Meter =====
+===== Previous generation =====
-Configuration\\
+==== DS1000 Single Phase Prepayment Meter ====
+Configuration\\
 DS1000  DS1000 measures reactive energy in addition to active energy and is ideally suited for utilities who wish to bill or monitor energy consumption based on Kilovolt-reactive-hour (kVArh) measurement. The meter offers additional instrumentation values and maximum demand as well.
   * Accuracy Class 1.0 to IEC 62053-21
   * Standard IEC 62055-31 for STS prepayment
   * Contactor Disconnect
   * Basic Feature      Extensive security data
   * High security, compact design
@@ Line 64: / Line 66: @@
   * 15 years service life
   * Unidirectional or bi-directional measurement
   * Metering Security
   * STS/CTS Compliance
   * Communication
@@ Line 74: / Line 76: @@
   * Display DS1000 can be configured by the customer to display English characters or OBIS identification codes.
   * An optional battery can support the display during power outages.
 ==== DS1600 Single Phase Smart Prepayment Meter  ====
@@ Line 109: / Line 112: @@
 The DSC100 is a DLMS and DL/T 698 compliant data concentrator whose primary function is to communicate between the Head End System (HES), and data streams collected from a variety of energy meters with different communication modules. The system is intended to provide reliable and secure data management for Advanced MeteringInfrastructure (AMI) and Post Event Analysis.
-The DSC100 system collects, processes, and reports data in compliance to DLMS, DL/T 698 from smart energy meter and system monitoring applications. Smart metering data from a variety of meters are time-aligned, structured, and transmitted to upstream devices, which can be similar DCU to smart meter, Super PDCs, visualization devices, external historians, or external applications. The DSC100 can be installed at the Transformer Level, or at a Regional Control Center. DONSUN’s data concentrator, DSC100, acquires metering data from various Energy Measurement Units (EMUs), such as the single-phase RF meter, PLC meter and three phase RF and PLC meter,and from other EMU devices with different reporting rates. The DSC100 can accommodate RF and PLC communication module for downlink to meters and GPRS/3G/4G modules for uplink to HES. All EMU data sent to the DSC100 must comply with DLMS or DL/T 698. The DSC100 system is a DLMS and DL/T 698 complaint DCU. This DSC100system can communicate with DLMS or DL/T 698 standard compliant EMU/DC devices. The primary functions of the DSC100 are to: • communicate with EMUs and other DCs (eg: super-DC) • acquire meter data from up to meters at different sites • time-scheduled data from various meters • filter and process the received data as required, if configured by the user • structure/aggregate output datasets from the available input data • archive and visualize the EMU data if it is ordered with the optional device and visualization tool for various real-time energy visualization applications. The DSC100 is a multi-processor computing platform comprising multiple single board computers: Processor Single Board Computer and one other Single Board Computer are housed in composite plastic case. To alleviate maintenance concerns, the DSC100’s design has eliminated the need for any moving parts, and it is cooled entirely by natural convection (for mounting requirements for cooling, see the Mechanical Installation > Mounting section below). In addition to its processor cards, the DSC100 device supports 2, 128 MB solid-state drives connected to the processor, should it be ordered, to serve as its archive location. Finally, though the base model of the DSC100 has 1 power supply (DC or Universal), it can be equipped with a fully redundant, current sharing mate. The DSC100 can be ordered with either a low voltage DC power supply or a high voltage universal AC/ DC power supply. Additionally, the device may be ordered with a fully redundant power supply. The DSC100’s power supply and its mate (if installed) are located adjacent to the input power board. A LED indicator has been provided to show the status of the supply. The input power requirements are also clearly indicated on the front of each supply.
+The DSC100 system collects, processes, and reports data in compliance to DLMS, DL/T 698 from smart energy meter and system monitoring applications. Smart metering data from a variety of meters are time-aligned, structured, and transmitted to upstream devices, which can be similar DCU to smart meter, Super PDCs, visualization devices, external historians, or external applications. The DSC100 can be installed at the Transformer Level, or at a Regional Control Center. DONSUN’s data concentrator, DSC100, acquires metering data from various Energy Measurement Units (EMUs), such as the single-phase RF meter, PLC meter and three phase RF and PLC meter,and from other EMU devices with different reporting rates. The DSC100 can accommodate RF and PLC communication module for downlink to meters and GPRS/3G/4G modules for uplink to HES. All EMU data sent to the DSC100 must comply with DLMS or DL/T 698. The DSC100 system is a DLMS and DL/T 698 complaint DCU. This DSC100system can communicate with DLMS or DL/T 698 standard compliant EMU/DC devices.
+The primary functions of the DSC100 are to:
+  * communicate with EMUs and other DCs (eg: super-DC)
+  * acquire meter data from up to meters at different sites
+  * time-scheduled data from various meters
+  * filter and process the received data as required, if configured by the user
+  * structure/aggregate output datasets from the available input data
+  * archive and visualize the EMU data if it is ordered with the optional device and visualization tool for various real-time energy visualization applications.
+The DSC100 is a multi-processor computing platform comprising multiple single board computers: Processor Single Board Computer and one other Single Board Computer are housed in composite plastic case. To alleviate maintenance concerns, the DSC100’s design has eliminated the need for any moving parts, and it is cooled entirely by natural convection (for mounting requirements for cooling, see the Mechanical Installation > Mounting section below). In addition to its processor cards, the DSC100 device supports 2, 128 MB solid-state drives connected to the processor, should it be ordered, to serve as its archive location. Finally, though the base model of the DSC100 has 1 power supply (DC or Universal), it can be equipped with a fully redundant, current sharing mate. The DSC100 can be ordered with either a low voltage DC power supply or a high voltage universal AC/ DC power supply. Additionally, the device may be ordered with a fully redundant power supply. The DSC100’s power supply and its mate (if installed) are located adjacent to the input power board. A LED indicator has been provided to show the status of the supply. The input power requirements are also clearly indicated on the front of each supply.
+{{ :home:technologies:donsunmetercatalog2019.pdf |Donsun Meter Catalog 2019}}